Altronix AL802ULADAJ Przewodnik Instalacji Pobierz pdf (Strona 4)

- 4 - AL802ULADAJ

Note: The 2-wire horn/strobe sync mode will only synchronize horns, horn/strobes, strobes with

synchronization capability.

7. For connection of smoke detectors, digital dialer (Optional Hookup Dia

gram, pg. 7).

Class A, Style Z Class B, Style W, Y, SW1 & SW2 Settings:

• For all Class B, Style W, Y, hookups SW1 & SW2 on the AL800LGK logic board must be open.

For all Class A, Style Z hookups SW1 & SW2 on the AL800LGK logic board must be closed.

Output Programming Selection Table:

Outputs must be programmed independently (OUT1 - OUT4)

For the above modes Dip Switch 4 determines which Input controls

the corr

esponding output:

Switch 4 in the ON position causes output(s) to be controlled by input 1.

Switch 4 in the OFF position causes output(s) to be controlled by input 2.

Sync Mode Selection Table:

*Note: The AL802ULADAJ will only synchronize horns, horn/strobes and strobes that contain synchronization capability.

Contact signal manufacturer for more detailed info. The same synchronization mode must be selected for all outputs.

(AL800LGK Board)

Output Dip Switches

INPUT SELECT

TEMPORAL

STROBE SYNC

IN>OUT SYNC

Function

Switch Positions

Descriptions

ON OFF

Input to Output Follower Mode 1 2, 3

Output follows signal it receives from the corresponding input

(i.e. FACP Sync module - maintains synchronization of

notification appliance circuit).

Temporal Code 3 Mode 3 1, 2

Enables Temporal Code 3 signal generation output.

This mode will accept a steady or a pulsing input.

Steady Mode 1, 2, 3

A steady output signal will be generated.

This mode will accept steady or pulsing input.

Function

Switch Positions

Descriptions

ON OFF

Amseco Sync

Mode*

1, 3,

This mode is designed to work with the Amseco series of horns, strobes, and

horn/strobes to provide a means of synchronizing the Temporal-coded horns,

synchronizing the flash timing of the strobe, and silencing the horns of the

horn/strobe combination over a two-wire circuit while leaving strobes active.

Faraday

Sync Mode*

2, 4 1, 3

This mode is designed to work with the Faraday series of horns, strobes, and

horn/strobes to provide a means of synchronizing the Temporal-coded horns,

synchronizing the flash timing of the strobe, and silencing the horns of the

horn/strobe combination over a two-wire circuit while leaving strobes active.

Gentex

Sync Mode*

Gentex is a registered trademark of

Gentex Corporation.

1, 2,

3, 4

This mode is designed to work with the Gentex

series of horns, strobes, and

horn/strobes to provide a means of synchronizing the Temporal-coded horns,

synchronizing the flash timing of the strobe, and silencing the horns of the

horn/strobe combination over a two-wire circuit while leaving strobes active.

System Sensor

Sync Mode*

System Sensor is a registered

trademark of Honeywell.

1, 2, 4 3

This mode is designed to work with the System Sensor

series of horns, strobes,

and horn/strobes to provide a means of synchronizing the Temporal-coded horns,

synchronizing the one-second flash timing of the strobe, and silencing the horns

of the horn/strobe combination over a two-wire circuit while leaving

strobes active.

CooperWheelock

Sync Mode*

CooperWheelock is a

registered trademark of

CooperWheelock.

2, 3, 4 1

This mode is designed to work with the CooperWheelock series of horns, strobes,

and horn/strobes to provide a means of synchronizing the Temporal-coded horns,

synchronizing the one-second flash timing of the strobe, and silencing the horns

of the horn/strobe combination over a two-wire circuit while leaving

strobes active.

1 2 3 4 5 6 7 8 9 10 11 12

Komentarze do niniejszej Instrukcji

Brak uwag

Altronix AL802ULADAJ Przewodnik Instalacji Strona 4

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Przedłużacze Altronix AL802ULADAJ